Trueness and precision of an intraoral scanner on abutments with subgingival vertical margins: An in vitro study.

OBJECTIVES: This study aimed to evaluate the accuracy of an intraoral scanner (IOS - Medit i700) on tooth abutments with vertical preparations at 2 depths below the free gingival margin, and to determine if the IOS can reproduce the area beyond the finish surface of the tested preparation geometry. METHODS: Two abutments for a maxillary first molar were designed by means of CAD software, with vertical preparations set at 1 and 2 mm below the gingiva. These abutments were subsequently printed in resin and placed on a reference model. The reference files consisted of scans made using a metrological machine on these abutments. Ten scans were made with the tested IOS on each sample, resulting in two study groups. The scans from the experimental groups were labeled "V-1″ for vertical preparation at 1 mm below the gingival margin and "V-2″ for 2 mm below. The analysis of these scans was performed using Geomagic Control X (3D SYSTEMS) to assess their trueness and precision in µm. Descriptive statistics with a 95 % confidence interval were employed, alongside independent sample tests, to ascertain any differences between the groups (α=0.05). RESULTS: Statistically significant differences were not found both for trueness (p=.104) and precision (p=.409), between the tested geometries. The mean values for trueness were V-1 = 37.5[31.4-43.6]; V-2 = 32.6[30.6-34.6]. About the precision, the mean values were V-1 = 20.5[8.4-32.5]; V-2 = 18.4[8.2-28.5]. In both the study groups, it was possible to detect the surface beyond the finish area. CONCLUSIONS: Within the limitations of this study, vertical preparation design allows for registration of the tooth anatomy beyond the finish area with IOS. Moreover, the mean accuracy values were clinically acceptable at both 1 and 2 mm below the gingival margin.

Trueness, precision, time-efficiency and cost analysis of chairside additive and subtractive versus lab-based workflows for manufacturing single crowns: An in vitro study.

PURPOSE: To evaluate the trueness, precision, time efficiency, and cost of three different workflows for manufacturing single crowns (SCs). METHODS: A plaster model with a prepared tooth (#15) was scanned with an industrial scanner, and an SC was designed in computer-assisted-design (CAD) software. Ten SCs were printed with a hybrid composite (additive chairside) and a stereolithographic (SLA) printer (Dfab®), 10 SCs were milled in lithium disilicate (subtractive chairside) using a chairside milling unit (inLab MC XL®), and 10 SCs were milled in zirconia (lab-based) using a five-axis laboratory machine (DWX-52D®). All SCs were scanned with the same scanner after polymerization/sinterization. Each scan was superimposed to the marginal area of the original CAD file to evaluate trueness: absolute average (ABS AVG), root mean square (RMS), and (90˚-10˚)/2 percentile were calculated for each group. Marginal adaptation and quality of the occlusal and interproximal contact points were also investigated by two prosthodontists on 3D printed and plaster models. Finally, the three workflows' time efficiency and costs were evaluated. RESULTS: Additive chairside and subtractive lab-based SCs had significantly better marginal trueness than subtractive chairside SCs in all three parameters (ABS AVG, p < 0.01; RMS, p < 0.01; [90˚-10˚]/2, p < 0.01). However, the two prosthodontists found no significant differences between the three manufacturing procedures in the quality of the marginal closure (p = 0.186), interproximal (p = 0.319), and occlusal contacts (p = 0.218). Both time efficiency and cost show a trend favoring the chairside additive workflow. CONCLUSIONS: Chairside additive technology seems to represent a valid alternative for manufacturing definitive SCs, given the high marginal trueness, precision, workflow efficiency and low costs. STATEMENT OF CLINICAL RELEVANCE: Additive chairside manufacturing of definitive hybrid composite SCs is now possible and shows high accuracy, time efficiency, and competitive cost.

Assessment of distortion of intraoral scans of edentulous mandibular arch made with a 2-step scanning strategy: A clinical study.

STATEMENT OF PROBLEM: Manufacturers of several intraoral scanners have recommended a 2-step strategy for scanning the edentulous mandible. The 2-step technique requires scanning one side first and then moving to the other side. However, whether inconsistency in stitching occurs that results in loss of accuracy or distortion is unclear. PURPOSE: The purpose of this clinical study was to measure the potential distortion of intraoral scans of edentulous mandibular arches made with a 2-step scanning strategy and to assess their differences with conventional impressions. MATERIAL AND METHODS: Twenty mandibular edentulous arches were scanned by 1 investigator with an intraoral scanner using a 2-step scanning strategy, and a corresponding polysulfide conventional impression was obtained. The conventional impression was then immediately scanned with the same intraoral scanner. The obtained standard tessellation language (STL) files were superimposed with a surface-matching software program. After a preliminary alignment, the STL meshes were trimmed and reoriented; then, the final alignment was carried out and meshes moved to a metrology software program where their mean distance was measured. In addition, a surface curve (SIOS) was traced on the intraoral scan from the right to left retromolar pad along the residual ridge and automatically projected onto to the conventional impression scan to obtain a new curve (SC). The mean distance between SIOS and SC was measured and recorded as an indicator of the distortion by considering the X-, Y-, and Z-axes and the overall 3-dimensional (3D) deviation. The analysis was performed for the full curve length and after dividing it into 6 regions of interest. Univariate and multivariate statistical analyses were used to investigate the significance of the extent of the mean 3D distance, as well as the effects of measurement positions (side and region) between and within patients on differences along the X-, Y-, and Z-axes (α=.05). RESULTS: The mean (-0.08 mm; standard error: 0.025) 3D distance between the intraoral scan and conventional impression was significantly different from zero (P=.003). No significant effect of the factor "side" was found by using generalized estimated equation models for the X-, Y-, and Z-axes, and global 3D deviations between SIOS and SC (P>.05), which appeared to exclude distortion. Conversely, a significant effect was found for the factor "region" (P<.05), with no significant differences (P>.05) between corresponding regions on the 2 sides. CONCLUSIONS: Intraoral scans of the edentulous mandibular arch made in a 2-step procedure did not exhibit significant distortion in comparison with conventional impressions.

Clinical longevity of direct and indirect posterior resin composite restorations: An updated systematic review and meta-analysis.

OBJECTIVES: To answer the PICO(S) question: Is there a difference in clinical longevity between direct and indirect resin composite restorations placed on permanent posterior teeth? DATA: Randomized controlled clinical trials (RCTs) investigating direct and indirect resin composite restorations in posterior permanent teeth were considered. SOURCES: Several electronic databases were searched, with no language or date restrictions. The revised Cochrane Collaboration's tool for assessing risk of bias (RoB-2) was used to analyze the studies; meta-analyses were run and the certainty of evidence was assessed by the GRADE tool. A subgroup meta-analysis was performed for resin composite restorations placed on posterior worn dentition. STUDY SELECTION: Twenty-three articles were included in qualitative synthesis, while 8 studies were used for meta-analyses. According to the RoB-2 tool, 5 studies were ranked as "low risk", 7 had "some concerns", while 11 papers were rated as "high risk" of bias. There were no statistically significant differences in short-term (p = 0.27; RR=1.54, 95% CI [0.72, 3.33]), medium-term (p = 0.27; RR=1.87, 95% CI [0.61, 5.72]) and long-term longevity (p = 0.86; RR=0.95, 95% CI [0.57, 1.59]). The choice of restorative technique had no influence on short-term survival of resin composite restorations placed on worn dentition (p = 0.13; RR=0.46, 95% CI [0.17, 1.25]). The certainty of evidence was rated as "very low". CONCLUSIONS: Direct and indirect resin composite restorations may show similar clinical longevity in posterior region, regardless of the observation period or substrate (wear-affected and non-affected dentition). The very low quality of evidence suggests that more long-term RCTs are needed to confirm our results.

Full Digital Workflow for Mandibular Ameloblastoma Management: Showcase for Technical Description.

This is a showcase for technical description of a full digital workflow aimed to reconstruct and prosthetically rehabilitate the mandible after surgical resection. The surgery was performed following a computer-aided design and computer-aided manufacturing (CAD-CAM) guided workflow, using 3D reconstruction of the mandible and the fibula. After 2 years, when the ossification of the flap was reached and verified by a computed tomography (CT) scan, surgery was performed using a two-step implant rehabilitation, with successful outcomes.

Dentin Exposure after Tooth Preparation for Laminate Veneers: A Microscopical Analysis to Evaluate the Influence of Operators' Expertise.

Background: To assess the quantity of dentin exposure detected by 3 operators with different clinical expertise for 2 designs of tooth preparation for laminate veneers: window (WI) and butt joint (BJ). Methods: 20 intact maxillary central incisors were collected and then prepared for laminate veneers to a depth of 0.6 mm, with a cervical mini-chamfer finish line of 0.3 mm. Each prepared tooth was analyzed by 3 operators with different expertise: undergraduate student (ST), general practitioner (GP), and prosthodontist (PR), at sight under magnification. Besides descriptive statistics (CI 95%), 2-way ANOVA and Games−Howell tests were used to analyze differences among groups (α = 0.05). Results: The means of percentage and area of detected dentin exposure were WI = 30.48%, 21.57 mm2; BJ = 30.99%, 21.97 mm2; ST/WI = 22.82%, 16.44 mm2; GP/WI = 58.05%, 40.64 mm2; PR/WI = 10.55%, 7.63 mm2; ST/BJ = 28.99%, 20.83 mm2; GP/BJ = 40.56%, 28.32 mm2; PR/BJ = 23.42%, 16.75 mm2. Significant differences were found between ST/WI vs. GP/WI (p = 0.005) and GP/WI vs. PR/WI (p < 0.001). Conclusions: There was no difference in detection of exposed dentin among operators with different expertise for BJ preparation, whereas differences were found between the general practitioner and the other 2 operators in WI. Moreover, the quantity of exposed dentin was not related to different tooth preparation designs.

Trueness and precision of 3D-printed versus milled monolithic zirconia crowns: An in vitro study.

PURPOSE: To compare the trueness and precision of 3D-printed versus milled monolithic zirconia crowns (MZCs). METHODS: A model of a maxilla with a prepared premolar was scanned with an industrial scanner (ATOSQ®, Gom) and an MZC was designed in computer-assisted-design (CAD) software (DentalCad®, Exocad). From that standard tessellation language (STL) file, 10 MZCs (test) were 3D-printed with a Lithography-based Ceramic Manufacturing (LCM) printer (CerafabS65®, Lithoz) and 10 MZCs (control) were milled using a 5-axis machine (DWX-52D®, DGShape). All MZCs were sintered and scanned with the aforementioned scanner. The surface data of each sample (overall crown, marginal area, occlusal surface) were superimposed to the original CAD file (ControlX®, Geomagic) to evaluate trueness: (90-10)/2, absolute average (ABS AVG) and root mean square (RMS) values were obtained for test and control groups (MathLab®, Mathworks) and used for analysis. Finally, the clinical precision (marginal adaptation, interproximal contacts) of test and control MZCs was investigated on a split-cast model printed (Solflex350®, Voco) from the CAD project, and compared. RESULTS: The milled MZCs had a significantly higher trueness than the 3D-printed ones, overall [(90-10)/2 printed 37.8 µm vs milled 21.2 µm; ABS AVG printed 27.2 µm vs milled 15.1 µm; RMS printed 33.2 µm vs milled 20.5 µm; p = 0.000005], at the margins [(90-10)/2 printed 25.6 µm vs milled 12.4 µm; ABS AVG printed 17.8 µm vs milled 9.4 µm; RMS printed 22.8 µm vs milled 15.6 µm; p= 0.000011] and at the occlusal level [(90-10)/2 printed 50.4 µm vs milled 21.9 µm; ABS AVG printed 29.6 µm vs milled 14.7 µm; RMS printed 38.9 µm vs milled 22.5 µm; p = 0.000005]. However, with regard to precision, both test and control groups scored highly, with no significant difference either in the quality of interproximal contact points (p = 0.355) or marginal closure (p = 0.355). CONCLUSIONS: Milled MZCs had a statistically higher trueness than 3D-printed ones; all crowns, however, showed high precision, compatible with the clinical use. CLINICAL SIGNIFICANCE: Although milled MZCs remain more accurate than 3D-printed ones, the LCM technique seems able to guarantee the production of clinically precise zirconia crowns.

Optical behaviors, surface treatment, adhesion, and clinical indications of zirconia-reinforced lithium silicate (ZLS): A narrative review.

OBJECTIVES: The present narrative review was focused on the optical properties, surface treatment, adhesion, and clinical indications of zirconia-reinforced lithium silicate ceramics (ZLS) for Computer-aided design / Computer-aided manufacturing (CAD/CAM) technologies. DATA/SOURCES: A literature search was performed by 3 calibrated independent researchers on PubMed, Scopus, Embase, Google Scholar, Dynamed, and Open Grey. The criteria for inclusion were: 1) papers addressing at least one of the following variables about ZLS: optical properties, surface treatment, adhesion, and clinical indications; 2) in vitro, in silico, or in vivo studies; 3) case reports; 4) systematic reviews. The exclusion criteria were: 1) animal studies; 2) non-dental studies; 3) studies only focusing on ZLS used in the heat-pressed process. STUDY SELECTION: 98 records among in vitro studies and case reports were included. CONCLUSIONS: Despite the promising microstructure characteristics of ZLS, increased translucency compared to lithium disilicate ceramics (LS2) was not proven, but acceptable color changes and stability were reported. Mechanical polishing was the most effective method to reduce surface roughness. Moreover, machinability and handling of ZLS resulted harder than LS2. Conventional acid etching procedures seemed effective in conditioning ZLS surface, but no protocol has been established yet. Besides, silane-coupling and dual-curing resin cements were recommended. CLINICAL SIGNIFICANCE: ZLSs can be used for anterior and posterior fixed single-unit CAD/CAM restorations onto both natural teeth and implants, but do not seem to represent a viable treatment option for endocrowns onto posterior teeth or fixed dental prostheses.

Zirconia-reinforced lithium silicate (ZLS) mechanical and biological properties: A literature review.

OBJECTIVES: This paper aimed to provide a literature review of the mechanical and biological properties of zirconia-reinforced lithium silicate glass-ceramics (ZLS) in Computer-aided design / Computer-aided manufacturing (CAD/CAM) systems. DATA/SOURCES: An extensive search of the literature for papers related to ZLS was made on the databases of PubMed/Medline, Scopus, Embase, Google Scholar, Dynamed, and Open Grey. The papers were selected by 3 independent calibrated reviewers. STUDY SELECTION: The search strategy produced 937 records. After the removal of duplicates and the exclusion of papers that did not meet the inclusion criteria, 71 papers were included. CONCLUSIONS: After reviewing the included records, it was found that two types of ZLS (Vita Suprinity PC; Vita Zahnfabrik and Celtra Duo; Dentsply Sirona) are nowadays available on the market for CAD/CAM systems, similar in their chemical composition, microstructure, and biological-mechanical properties. ZLS is reported to be a biocompatible material, whose fracture resistance can withstand physiological chewing loads. The firing process influences the improvements of strength and fatigue failure load, with a volumetric shrinkage. To date, ZLS can be considered a viable alternative to other glass-ceramics for fixed single restorations. CLINICAL SIGNIFICANCE: . As to biocompatibility and mechanical properties of ZLS, data are still scarce, often controversial and limited to short-term observational periods. These promising ceramics require further in vitro/in vivo studies to accurately define mechanical and biological properties, mainly in the long-term performance of restorations produced with such materials.

Analysis of The Reproducibility of Subgingival Vertical Margins Using Intraoral Optical Scanning (IOS): A Randomized Controlled Pilot Trial.

BACKGROUND: The aim of this randomized controlled trial was to evaluate the capability of an IOS (Intra Oral Scanner) device, used in standardized conditions, to detect margins of abutments prepared with knife-edge finishing line located at three different levels in relation to the gingival sulcus. METHODS: sixty abutment teeth for treatment with full crowns were selected and randomly divided in three groups accordingly to the depth of the finishing line: Group A: supragingival margin; Group B: 0.5-1.0 mm into the sulcus; Group C: 1.5-2.0 mm into the sulcus. Temporary crowns were placed for two weeks and then digital impressions (Aadva IOS 100, GC, Japan) were made of each abutment. As controls, analog impressions were taken, poured, and scanned using a laboratory scanner (Aadva lab scanner, GC, Japan). Two standard tessellation language (STL) files were generated for each abutment, subsequently processed, and superimposed by Exocad software (Exocad GmbH, Darmstadt, Germany), applying the "best-fit" algorithm in order to align the scan of the conventional with the digital impressions. The distances between each preparation margin and the adjacent gingival tissue were measured. Four measures were taken, two interproximally and buccally, for a total of six measures of each abutment considering three modes of impressions. The data were statistically evaluated using two-way analysis of variance (ANOVA) for each site and the Bonferroni test. RESULTS: there was no difference between the two kinds of impression in Group A in both sites, in Group B a difference of 0.483 mm and 0.682 mm at interproximal and buccal sites, respectively, and in Group C 0.750 mm and 0.964 mm at interproximal and buccal sites, respectively. The analysis performed on a site level (mesial/distal/vestibular) for the depth of both vertical preparations revealed significant differences (p < 0.0001). After a post hoc analysis (Bonferroni), vestibular sites of the shallow vertical preparations resulted in significantly lower values compared to the other sites prepared deeply. CONCLUSIONS: the results showed that the location of the margin is an important factor in making a precise and complete impression when IOS (Intra Oral Scanner) is used. Moreover, deep preparation into the sulcus is not recommended for IOS (Intra Oral Scanner) impressions.

Accuracy of a chairside intraoral scanner compared with a laboratory scanner for the completely edentulous maxilla: An in vitro 3-dimensional comparative analysis.

STATEMENT OF PROBLEM: Intraoral scanners are promising options for removable prosthodontics. However, analog aids, including occlusion rims, are still used, as a completely digital workflow is challenging and scientific evidence on the topic is scarce. PURPOSE: The purpose of this in vitro study was to assess and compare the trueness and precision of scans obtained from a reference typodont of a completely edentulous maxilla by using an intraoral scanner (TRIOS 3 Pod; 3Shape A/S) with scans obtained by using a laboratory scanner (DScan 3; EGS S.R.L.) from both Type IV stone casts and polysulfide impressions. MATERIAL AND METHODS: The polyurethane resin reference typodont was replicated from a clinical cast and was scanned with a metrological machine to obtain a reference scan. Ten digital casts were obtained by applying standardized scanning strategies to the reference typodont with the intraoral scanner. A device was created to make 10 consistent polysulfide impressions, and a scan of each impression was made with the laboratory scanner and then digitally reversed to obtain 10 digital reversed casts. Ten Type IV stone casts were poured and then scanned with the laboratory scanner to obtain 10 digital extraoral scanner casts. The scans in standard tessellation language (STL) format were imported into a dedicated software program, and the trueness and precision were calculated in µm. In addition to descriptive statistics (confidence interval 95%), 1-way ANOVA followed by the Bonferroni test or the Kruskal-Wallis and the Dunn tests were used to analyze differences among groups (α=.05). RESULTS: The trueness values (95% confidence interval) were digital intraoral scanner cast=48.7 (37.8-59.5), digital reversed cast=249.9 (121.3-378.5), and digital extraoral scanner cast=308.8 (186.6-430.9); significant differences were detected between digital intraoral scanner cast and digital reversed cast (P<.001) and between digital IOS casts and digital extraoral scanner cast (P<.001). The precision values (95% confidence interval) were digital intraoral scanner cast=46.7 (29.7-63.7), digital reversed cast=271.2 (94.6-447.8), and digital extraoral scanner cast=341.4 (175.5-507.3); significant differences were detected between digital intraoral scanner cast and digital reversed cast (P=.003) and between digital intraoral scanner cast and digital extraoral scanner cast (P=.001). CONCLUSIONS: Directly scanning a solid typodont of a completely edentulous maxilla with the intraoral scanner produced better trueness and precision than scanning the polysulfide impressions or the stone casts with a laboratory scanner.

Comparison of different intraoral scanning techniques on the completely edentulous maxilla: An in vitro 3-dimensional comparative analysis.

STATEMENT OF PROBLEM: Information about the accuracy of intraoral scanners for the edentulous maxilla is lacking. PURPOSE: The purpose of this in vitro study was to compare the accuracy of 3 different intraoral scanner techniques on a completely edentulous maxilla typodont. MATERIAL AND METHODS: Two completely edentulous maxillary typodonts with (wrinkled typodont) and without (smooth typodont) palatal rugae were used as reference and were scanned by using an industrial metrological machine to obtain 2 digital reference scans in standard tessellation language (STL) format (dWT and dST). Three different scanning techniques were investigated: in the buccopalatal technique, the buccal vestibule was scanned with a longitudinal movement ending on the palatal vault with a posteroanterior direction; the S-shaped technique was based on an alternate palatobuccal and buccopalatal scan along the ridge; in the palatobuccal technique, the palate was scanned with a circular movement and then with a longitudinal one along the buccal vestibule. Consecutively, 6 types of scans were obtained (n=10), namely wrinkled typodont/buccopalatal technique, wrinkled typodont/S-shaped technique, wrinkled typodont/palatobuccal technique (wrinkled typodont), smooth typodont/buccopalatal technique, smooth typodont/S-shaped technique, and smooth typodont/palatobuccal technique (smooth typodont). Scans in STL format were imported into a dedicated software program, and trueness and precision were evaluated in µm. In addition to descriptive statistics (95% confidence interval), a 2-factor ANOVA on the data ranks, the Kruskal-Wallis, and the Dunn tests were performed to analyze differences among groups (α=.05). RESULTS: Mean values for trueness (95% confidence interval) were wrinkled typodont/buccopalatal technique=48.7 (37.8-59.5); wrinkled typodont/S-shaped technique=65.9 (54.9-77.4); wrinkled typodont/palatobuccal technique=109.7 (96.1-123.4); smooth typodont/buccopalatal technique=48.1 (42.4-53.7); smooth typodont/S-shaped technique=56.4 (43.9-68.9); smooth typodont/palatobuccal technique=61.1 (53.3-69), with statistically significant differences for wrinkled typodont/buccopalatal technique versus wrinkled typodont/palatobuccal technique (P<.001), buccopalatal technique versus palatobuccal technique (P<.001), and wrinkled typodont versus smooth typodont (P=.002). Mean values for precision (95% confidence interval) were wrinkled typodont/buccopalatal technique=46.7 (29.7-63.7); wrinkled typodont/S-shaped technique=53.6 (37.6-69.7); wrinkled typodont/palatobuccal technique=90 (59.1-120.9); smooth typodont/buccopalatal technique=46 (39.7-52.3); smooth typodont/S-shaped technique=76 (55.5-96.6); smooth typodont/palatobuccal technique=52.9 (41.9-63.8); with statistically significant differences for buccopalatal technique versus palatobuccal technique (P=.032) and wrinkled typodont/buccopalatal technique versus wrinkled typodont/palatobuccal technique (P=.012). CONCLUSIONS: Smooth typodont scans showed better trueness than wrinkled typodont scans. Buccopalatal technique showed better mean values for trueness and precision than palatobuccal technique only in the wrinkled typodont scenario, while the other scanning approaches did not show significant differences in either tested configuration.

Fourteen-year evaluation of posterior zirconia-based three-unit fixed dental prostheses: A Prospective clinical study of all ceramic prosthesis.

OBJECTIVES: the purpose of the present prospective trial was to evaluate the clinical performance of posterior 3-unit zirconia-based fixed dental prostheses (FDPs) after 14 years of clinical function. METHODS: thirty-seven patients needing to replace either premolars or molars were involved and 48 FDPs were fabricated (Procera Zirconia, Nobel Biocare AB). Frameworks with a9 mm2 cross section of the connectors and 0.6 mm minimum thickness of the retainers were made by means of Procera Forte CAD-CAM System (Nobel Biocare AB). The patients were recalled after 6 and 12 months and then yearly up to a total follow-up of 14 years. Two independent survival curves for patients wearing 1 or 2 FDPs were calculated by means of Kaplan-Meier analysis and a log-rank test was performed in order to compare these curves. The United States Public Health Service criteria were used to examine technical and esthetic outcomes. The biological examination was performed evaluating plaque control, pocket depth, attachment level, bleeding on probing at both abutments and contralateral teeth and evaluated by means of the Wilcoxon test (p < 0.05) between the baseline and the 14-year follow-up. RESULTS: descriptive statistics resulted in 91 % and 99 % cumulative survival rates for patients wearing 1 and 2 FDPs, respectively. There were no significant differences in periodontal parameters between control and test teeth. Both function and esthetic results were successful for FDPs over a 14-year follow-up period. CONCLUSIONS: the results of this prospective clinical study confirmed the effectiveness of zirconia as a clinical option to fabricate short-span posterior FDPs. CLINICAL SIGNIFICANCE: within the limitations of the present prospective clinical study, zirconia-based three-unit fixed dental prostheses perform satisfactorily on long term, in posterior areas and in patients with standard biomechanical conditions.

Accuracy of Three Impression Materials on the Totally Edentulous Maxilla: In Vitro/In Silico Comparative Analysis.

BACKGROUND: This study was aimed at comparing the accuracy of impressions of a reference typodont (RT) reproducing a totally edentulous maxilla made with three impression materials: polysulfide, polyether, and polyvinyl-siloxane. METHODS: The RT was scanned using a desktop scanner, obtaining a reference scan. Ten impressions for each of the three tested materials were made using a mechanical device with a standardized and consistent modality. A laboratory scanner performed the digitization of each impression. We produced digital models by processing "in reverse" the scans of the physical impressions using a dedicated software, obtaining three groups (n = 10), respectively. The groups were titled: "polysulfide," "polyvinyl-siloxane," and "polyether." The scans in .stl format were imported into Geomagic Control X and then compared to RT to evaluate the accuracy of each scan by calculating trueness and precision in µm. Recorded data were subjected to descriptive statistics. RESULTS: Trueness (arithmetic proximity) values (95%CI) were: polysulfide = 249.9 (121.3-378.5), polyvinyl-siloxane = 216.8 (123.1-310.6), polyether = 291.1 (219.9-362.3). Precision values (95% CI) were: polysulfide = 261.9 (108.8-415), polyvinyl-siloxane = 209.4 (111.9-306.8), polyether = 283 (227.9-338.1). Statistically significant differences were not detected between the means of the experimental groups, both for trueness and precision. CONCLUSIONS: The accuracy of the scans obtained from polyvinyl-siloxane, polysulfide, and polyether impressions can be considered comparable in a fully edentulous maxilla.

Mechanical behavior of conceptual posterior dental crowns with functional elasticity gradient.

PURPOSE: To evaluate the biomechanical behavior of monolithic ceramic crowns with functional elasticity gradient. METHODS: Using a CAD software, a lower molar received a full-crown preparation (1.5 mm occlusal and axial reduction). The monolithic crown was modeled with a resin cement layer of 0.1 mm. Four groups were distributed according to the full crown elastic modulus (E) :(a) Bioinspired crown with decreasing elastic modulus (from 90 to 30GPa); (b) Crown with increasing elastic modulus (from 30 to 90 GPa); (c) Rigid crown (90 GPa) and (d) Flexible crown (30 GPa). The model was exported to the analysis software and meshed into 385.240 tetrahedral elements and 696.310 nodes. Materials were considered isotropic, linearly elastic, and homogeneous, with ideal contacts. A 300-N load was applied at the occlusal surface and the base of the model was fixed in all directions. The results were required in maximum principal stress criterion. RESULTS: Crowns consisting of layers with increasing elastic modulus presented intermediate results between the rigid and flexible crowns. Compared to the flexible crown, the bioinspired crown showed acceptable stress distribution across the structure with lower stress concentration in the tooth. In dental crowns the multilayer structure with functional elasticity gradient modifies the stress distribution in the restoration, with promising results for bioinspired design. CLINICAL SIGNIFICANCE: The manufacturing of posterior crowns with functional elasticity gradient should be considered due to its promising results on the stress concentration behavior.

Current status on lithium disilicate and zirconia: a narrative review.

BACKGROUND: The introduction of the new generation of particle-filled and high strength ceramics, hybrid composites and technopolymers in the last decade has offered an extensive palette of dental materials broadening the clinical indications in fixed prosthodontics, in the light of minimally invasive dentistry dictates. Moreover, last years have seen a dramatic increase in the patients' demand for non-metallic materials, sometimes induced by metal-phobia or alleged allergies. Therefore, the attention of scientific research has been progressively focusing on such materials, particularly on lithium disilicate and zirconia, in order to shed light on properties, indications and limitations of the new protagonists of the prosthetic scene. METHODS: This article is aimed at providing a narrative review regarding the state-of-the-art in the field of these popular ceramic materials, as to their physical-chemical, mechanical and optical properties, as well as to the proper dental applications, by means of scientific literature analysis and with reference to the authors' clinical experience. RESULTS: A huge amount of data, sometimes conflicting, is available today. Both in vitro and in vivo studies pointed out the outstanding peculiarities of lithium disilicate and zirconia: unparalleled optical and esthetic properties, together with high biocompatibility, high mechanical resistance, reduced thickness and favorable wear behavior have been increasingly orientating the clinicians' choice toward such ceramics. CONCLUSIONS: The noticeable properties and versatility make lithium disilicate and zirconia materials of choice for modern prosthetic dentistry, requiring high esthetic and mechanical performances combined with a minimal invasive approach, so that the utilization of such metal-free ceramics has become more and more widespread over time.

Effects of Finish Line Design and Fatigue Cyclic Loading on Phase Transformation of Zirconia Dental Ceramics: A Qualitative Micro-Raman Spectroscopic Analysis.

OBJECTIVES: Stresses produced during the fabrication of copings and by chewing activity can induce a tetragonal-to-monoclinic (t⁻m) transformation of zirconia. As a consequence, in the m-phase, the material is not able to hinder possible cracks by the favorable mechanism known as "transformation toughening". This study aimed at evaluating if different marginal preparations of zirconia copings can cause a premature phase transformation immediately after manufacturing milling and after chewing simulation. METHODS: Ninety copings using three commercial zirconia ceramics (Nobel Procera Zirconia, Nobel Biocare Management AG; Lava Classic, 3M ESPE; Lava Plus, 3M ESPE) were prepared with deep-chamfer, slight-chamfer, or feather-edge finish lines (n = 10). Specimens were tested in a chewing simulator (CS-4.4, SD Mechatronik) under cyclic occlusal loads simulating one year of clinical service. Raman spectra were acquired and analyzed for each specimen along the finish lines and at the top of each coping before and after chewing simulation, respectively. RESULTS: Raman analysis did not show any t⁻m transformation both before and after chewing simulation, as the typical monoclinic bands at 181 cm-1 and 192 cm-1 were not detected in any of the tested specimens. CONCLUSIONS: After a one-year simulation of chewing activity, irrespective of preparation geometry, zirconia copings did not show any sign of t⁻m transformation, either in the load application areas or at the margins. Consequently, manufacturing milling even in thin thickness did not cause any structural modification of zirconia ceramics "as received by manufacturers" both before and after chewing simulation.

The Functional Implant Prosthodontic Score (FIPS): assessment of reproducibility and observer variability.

OBJECTIVES: The aim of this study was to validate the reproducibility and observer variability of the Functional Implant Prosthodontic Score (FIPS), while considering the level of dental experience for intra- and inter-examiner analysis. MATERIALS AND METHODS: A total of 44 examiners (n = 31 undergraduate dental students and n = 13 postgraduate prosthodontic students) applied FIPS to ten sample cases each showing one implant-supported single crown for premolar or molar replacements. Examiners' assessments were carried out twice at an interval of 2 weeks (round A and round B). Pearson's correlations including 95% confidence intervals (CI95) were calculated for intra- and inter-examiner reproducibility testing. Cohen's Kappa score was additionally used to analyze the homogeneity of each FIPS variable. RESULTS: The mean values of the total FIPS scores for round A (7.21 ± 0.91) and round B (7.27 ± 0.86) showed a strong correlation of 0.9374 (CI95 0.9250; 0.9478). No significant difference was identified between undergraduates and postgraduates representing different levels of dental experience. Homogeneity analysis of the defined FIPS variables was not significantly different. CONCLUSIONS: Both intra- and inter-examiner analysis revealed very congruent results for reproducibility testing of FIPS. The findings validated the potential of FIPS as an objective and reliable evaluation instrument in assessing fixed implant restorations in posterior sites independent of the level of dental experience. CLINICAL RELEVANCE: FIPS can be considered as an additional diagnostic tool to classify fixed implant restorations in routine dental practice, to compare follow-up observations, and to identify potential risks of failure.

Mechanical behavior of endodontically restored canine teeth: Effects of ferrule, post material and shape.

OBJECTIVE: To assess the effect of a ferrule design with specific post material-shape combinations on the mechanical behavior of post-restored canine teeth. METHODS: Micro-CT scan images of an intact canine were used to create a 3-D tessellated CAD model, from which the shapes of dentin, pulp and enamel were obtained and geometric models of post-endodontically restored teeth were created. Two types of 15mm post were evaluated: a quartz fiber post with conical-tapered shape, and a carbon (C) fiber post with conical-cylindrical shape. The abutment was created around the coronal portion of the posts and 0.1mm cement was added between prepared crown and abutment. Cement was also added between the post and root canal and a 0.25mm periodontal ligament was modeled around the root. Four models were analysed by Finite Element (FE) Analysis: with/without a ferrule for both types of post material and shape. A load of 50N was applied at 45° to the longitudinal axis of the tooth, acting on the palatal surface of the crown. The maximum normal stress criterion was adopted as a measure of potential damage. RESULTS: Models without a ferrule showed greater stresses (16.3MPa) than those for models with a ferrule (9.2MPa). With a ferrule, stress was uniformly distributed along the abutment and the root, with no critical stress concentration. In all models, the highest stresses were in the palatal wall of the root. Models with the C-fiber post had higher stress than models with the quartz fiber posts. The most uniform stress distribution was with the combination of ferrule and quartz fiber post. SIGNIFICANCE: The FE analysis confirmed a beneficial ferrule effect with the combination of ferrule and quartz fiber post, with tapered shape, affording no critical stress concentrations within the restored system.

The complete digital workflow in fixed prosthodontics: a systematic review.

BACKGROUND: The continuous development in dental processing ensures new opportunities in the field of fixed prosthodontics in a complete virtual environment without any physical model situations. The aim was to compare fully digitalized workflows to conventional and/or mixed analog-digital workflows for the treatment with tooth-borne or implant-supported fixed reconstructions. METHODS: A PICO strategy was executed using an electronic (MEDLINE, EMBASE, Google Scholar) plus manual search up to 2016-09-16 focusing on RCTs investigating complete digital workflows in fixed prosthodontics with regard to economics or esthetics or patient-centered outcomes with or without follow-up or survival/success rate analysis as well as complication assessment of at least 1 year under function. The search strategy was assembled from MeSH-Terms and unspecific free-text words: {(("Dental Prosthesis" [MeSH]) OR ("Crowns" [MeSH]) OR ("Dental Prosthesis, Implant-Supported" [MeSH])) OR ((crown) OR (fixed dental prosthesis) OR (fixed reconstruction) OR (dental bridge) OR (implant crown) OR (implant prosthesis) OR (implant restoration) OR (implant reconstruction))} AND {("Computer-Aided Design" [MeSH]) OR ((digital workflow) OR (digital technology) OR (computerized dentistry) OR (intraoral scan) OR (digital impression) OR (scanbody) OR (virtual design) OR (digital design) OR (cad/cam) OR (rapid prototyping) OR (monolithic) OR (full-contour))} AND {("Dental Technology" [MeSH) OR ((conventional workflow) OR (lost-wax-technique) OR (porcelain-fused-to-metal) OR (PFM) OR (implant impression) OR (hand-layering) OR (veneering) OR (framework))} AND {(("Study, Feasibility" [MeSH]) OR ("Survival" [MeSH]) OR ("Success" [MeSH]) OR ("Economics" [MeSH]) OR ("Costs, Cost Analysis" [MeSH]) OR ("Esthetics, Dental" [MeSH]) OR ("Patient Satisfaction" [MeSH])) OR ((feasibility) OR (efficiency) OR (patient-centered outcome))}. Assessment of risk of bias in selected studies was done at a 'trial level' including random sequence generation, allocation concealment, blinding, completeness of outcome data, selective reporting, and other bias using the Cochrane Collaboration tool. A judgment of risk of bias was assigned if one or more key domains had a high or unclear risk of bias. An official registration of the systematic review was not performed. RESULTS: The systematic search identified 67 titles, 32 abstracts thereof were screened, and subsequently, three full-texts included for data extraction. Analysed RCTs were heterogeneous without follow-up. One study demonstrated that fully digitally produced dental crowns revealed the feasibility of the process itself; however, the marginal precision was lower for lithium disilicate (LS2) restorations (113.8 µm) compared to conventional metal-ceramic (92.4 µm) and zirconium dioxide (ZrO2) crowns (68.5 µm) (p < 0.05). Another study showed that leucite-reinforced glass ceramic crowns were esthetically favoured by the patients (8/2 crowns) and clinicians (7/3 crowns) (p < 0.05). The third study investigated implant crowns. The complete digital workflow was more than twofold faster (75.3 min) in comparison to the mixed analog-digital workflow (156.6 min) (p < 0.05). No RCTs could be found investigating multi-unit fixed dental prostheses (FDP). CONCLUSIONS: The number of RCTs testing complete digital workflows in fixed prosthodontics is low. Scientifically proven recommendations for clinical routine cannot be given at this time. Research with high-quality trials seems to be slower than the industrial progress of available digital applications. Future research with well-designed RCTs including follow-up observation is compellingly necessary in the field of complete digital processing.